This is the same temperature sensor that is included in our SparkFun Inventor’s Kit. The TMP36 is a low voltage, precision centigrade temperature sensor. It provides a voltage output that is linearly proportional to the Celsius temperature.
This is the latest DS18B20 1-Wire digital temperature sensor from Maxim IC. Reports degrees C with 9 to 12-bit precision, -55C to 125C (+/-0.5C). Each sensor has a unique 64-Bit Serial number etched into it - allows for a huge number of sensors to be used on one data bus. This is a wonderful part that is the corner stone of many data-logging and...
This sealed digital temperature probe lets you precisely measure temperatures in wet environments with a simple 1-Wire interface. The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface, so that only one wire (and ground) needs to be connected from a central microprocessor.
10K thermistor with a negative temperature coefficient. Good choice for temp-sensing applications when you need a reliable NTC thermistor.
Attach an Omega K-Type thermocouple to this adapter for a convenient way to connect it to a terminal block.
LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They’re even washable!
Communication with the TMP102 is achieved through a two-wire serial interface. There is no on-board voltage regulator, so supplied voltage should be between 1.4 to 3.6VDC. Filtering capacitors and pull-up resistors are included as shown.
36" high temperature Type-K Thermocouple with glass braid insulation.
This is the SparkFun Pi Wedge, a small board that connects to the 40-pin GPIO connector on the Raspberry Pi and breaks the pins out to breadboard-friendly arrangement and spacing, and even adds a couple of decoupling capacitors on the power supply lines. The “Wedge” also makes the initial bring-up process easier - you can plug an FTDI Basic...
The RHT03 (also known by DHT-22) is a low cost humidity and temperature sensor with a single wire digital interface. The sensor is calibrated and doesn’t require extra components so you can get right to measuring relative humidity and temperature.
The heart of the MP3 Trigger board is the Cypress PSoC CY8C29466-24SXI microcontroller which serves up MP3 data to a VLSI VS1063 audio codec IC.
Melexis' MLX90614ESF-BAA is an infrared thermometer designed for non-contact temperature sensing. An internal 17-bit ADC and a powerful DSP contribute to the MLX90614’s high accuracy and resolution. It has a huge number of applications including body temperature measurment and movement detection.
The MLX9061 sensor is a high precision, small size, single zone IR thermometer with an optional SMBus (two-wire) or PWM interface. The ATMega328 comes with demo code that gives a temperature readout in degrees F at 38400bps. You can use a 3.3V FTDI Basic to connect to the board.
You can apply Bare’s Electric Paint like any other water-based paint.
The TMP006 Breakout has a wide temperature detection range of -40°C to 125°C and an optimal operating voltage of 3.3V to 5V (tolerant up to 7V max). This breakout works great with most micro controllers connecting via the I2C bus.
Tilslut op til 4 termoelementer til dette board, og mål temperaturen i realtime . Sættes direkte i en USB-port.Sensoren kan anvendes sammen med Artisan coffee roasting software.
Equipped with the increasingly popular SAMD21 onboard, all you need is to assemble the SparkFun Wireless Joystick into the configuration you want and add your own XBee and lithium ion battery into the provided sockets.
The Gizmo Kit includes the base to hold and connect up to four Modulo modules, a powerful Arduino-compatible microcontroller, a knob module (rotation encoder, push button, bright RGB LED), an infrared remote transmitter/receiver, a micro servo motor (with included servo horns), and a microUSB cable. You can build all sort of things with the Gizmo Kit!
The Spectacle Light Board allows you to add some fairly complex lighting effects to your Spectacle projects in a streamlined manner. Each has connections for you to add addressable LEDs as well as an external power connector.
This non-contact infrared thermometer makes it a breeze to take quick and accurate surface temperature readings without getting too close for comfort. Laser sighting ensures that you’re pointing at the right spot: Simply pull the trigger and line up the laser dot where you want to measure the temperature.
With the SparkFun Thermocouple Breakout, the thermocouple’s hot junction can be read from -200°C to +700°C with an accuracy of ±2°C while the cold junction, inside the MAX31855K, can only range from -20°C to +85°C while maintaining ±2°C accuracy. The MAX31855K constantly measures the temperature of the cold junction using an internal temperature-sensing...
The TMP102 is an easy-to-use digital temperature sensor from Texas Instruments. The TMP102 breakout allows you to easily incorporate the digital temperature sensor into your project. While some temperature sensors use an analog voltage to represent the temperature, the TMP102 uses the I
If you plan on using this connector with a custom PCB make sure to check out the Datasheet in the Documents section below for mounting dimensions.
The pinout of the Serial Basic mimics the common DTR/RX/TX/VCC/CTS/GND pinout found on hundreds of FTDI-to-USB derivatives. It can also be used as a general serial device for debugging (such as with a GPS module). There is a jumper on the rear of the board that controls the output voltage on the VCC pin. By default, the board outputs 3.3V and has 3.3V...
Digital calipers are an absolute essential. Here at SparkFun we use them all the time. These premium calipers come with an extra battery and auto shut-off. Measurements can be taken in either metric or standard. The calipers are 6" in length and make a great addition to any tool set.
This common Type-K Thermocouple is made out of chromel and alumel, while offering a temperature high of 400°C and a low of 0°C. The probe itself is only 200mm (7.8in) long with a diameter of 5mm (~0.2in) and is terminated with a standard thermocouple connector.
For the FemtoBuck, we’ve increased the voltage ratings on the parts to allow the input voltage to cover the full 36V range of the AL8805 driver. Since the FemtoBuck is a constant current driver, the current drawn from the supply will drop as supply voltage rises. In general, efficiency of the FemtoBuck is around 95%, depending on the input voltage.
Each SparkFun Snappable Protoboard features a 0.1" spaced, 50x25 Solder Point array totaling up to an impressive 1250 PTH pins that can be broken apart to form a 2x2, 1x50, 24x42, or any size whatsoever as long as it is within the original array size. Don’t think of this as just one protoboard, think of it as any number you need.
The device communicates over a one-wire bus that, by definition, requires only one data line (and ground) for communication with a central microprocessor. In addition, the device can derive power directly from the data line, eliminating the need for an external power supply. Requiring so few pins enables the device to be placed in a 3-pin TO-92 package.